Filtered by vendor Cisco
Subscriptions
Filtered by product Ios
Subscriptions
Total
616 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2024-20276 | 1 Cisco | 10 Catalyst 6503-e, Catalyst 6504-e, Catalyst 6506-e and 7 more | 2025-08-05 | 7.4 High |
| A vulnerability in Cisco IOS Software for Cisco Catalyst 6000 Series Switches could allow an unauthenticated, adjacent attacker to cause an affected device to reload unexpectedly. This vulnerability is due to improper handling of process-switched traffic. An attacker could exploit this vulnerability by sending crafted traffic to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a denial of service (DoS) condition. | ||||
| CVE-2025-20151 | 1 Cisco | 4 Cisco Ios, Ios, Ios Xe and 1 more | 2025-08-05 | 4.3 Medium |
| A vulnerability in the implementation of the Simple Network Management Protocol Version 3 (SNMPv3) feature of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to poll an affected device using SNMP, even if the device is configured to deny SNMP traffic from an unauthorized source or the SNMPv3 username is removed from the configuration. This vulnerability exists because of the way that the SNMPv3 configuration is stored in the Cisco IOS Software and Cisco IOS XE Software startup configuration. An attacker could exploit this vulnerability by polling an affected device from a source address that should have been denied. A successful exploit could allow the attacker to perform SNMP operations from a source that should be denied. Note: The attacker has no control of the SNMPv3 configuration. To exploit this vulnerability, the attacker must have valid SNMPv3 user credentials. For more information, see the section of this advisory. | ||||
| CVE-2025-20137 | 1 Cisco | 41 Catalyst 1000-16fp-2g-l, Catalyst 1000-16p-2g-l, Catalyst 1000-16t-2g-l and 38 more | 2025-08-05 | 4.7 Medium |
| A vulnerability in the access control list (ACL) programming of Cisco IOS Software that is running on Cisco Catalyst 1000 Switches and Cisco Catalyst 2960L Switches could allow an unauthenticated, remote attacker to bypass a configured ACL. This vulnerability is due to the use of both an IPv4 ACL and a dynamic ACL of IP Source Guard on the same interface, which is an unsupported configuration. An attacker could exploit this vulnerability by attempting to send traffic through an affected device. A successful exploit could allow the attacker to bypass an ACL on the affected device. Note: Cisco documentation has been updated to reflect that this is an unsupported configuration. However, Cisco is publishing this advisory because the device will not prevent an administrator from configuring both features on the same interface. There are no plans to implement the ability to configure both features on the same interface on Cisco Catalyst 1000 or Catalyst 2960L Switches. | ||||
| CVE-2025-20181 | 1 Cisco | 44 Catalyst 2960cx-8pc-l, Catalyst 2960cx-8tc-l, Catalyst 2960x-24pd-l and 41 more | 2025-08-04 | N/A |
| A vulnerability in Cisco IOS Software for Cisco Catalyst 2960X, 2960XR, 2960CX, and 3560CX Series Switches could allow an authenticated, local attacker with privilege level 15 or an unauthenticated attacker with physical access to the device to execute persistent code at boot time and break the chain of trust. This vulnerability is due to missing signature verification for specific files that may be loaded during the device boot process. An attacker could exploit this vulnerability by placing a crafted file into a specific location on an affected device. A successful exploit could allow the attacker to execute arbitrary code at boot time. Because this allows the attacker to bypass a major security feature of the device, Cisco has raised the Security Impact Rating (SIR) of this advisory from Medium to High. | ||||
| CVE-2022-20920 | 1 Cisco | 2 Ios, Ios Xe | 2025-08-01 | 7.7 High |
| A vulnerability in the SSH implementation of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause an affected device to reload. This vulnerability is due to improper handling of resources during an exceptional situation. An attacker could exploit this vulnerability by continuously connecting to an affected device and sending specific SSH requests. A successful exploit could allow the attacker to cause the affected device to reload. | ||||
| CVE-2017-6744 | 1 Cisco | 1 Ios | 2025-07-31 | 8.8 High |
| The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities. | ||||
| CVE-2017-6743 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-31 | 8.8 High |
| The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities. | ||||
| CVE-2017-6742 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-31 | 8.8 High |
| A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device. The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability. | ||||
| CVE-2017-6740 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-31 | 8.8 High |
| The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities. | ||||
| CVE-2017-6739 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-31 | 8.8 High |
| A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device. The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability. | ||||
| CVE-2017-6738 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-31 | 8.8 High |
| The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities. | ||||
| CVE-2017-6737 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-31 | 8.8 High |
| A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device. The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability. | ||||
| CVE-2017-6736 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-31 | 8.8 High |
| The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities. | ||||
| CVE-2025-20154 | 1 Cisco | 3 Ios, Ios Xe, Ios Xr | 2025-07-31 | 8.6 High |
| A vulnerability in the Two-Way Active Measurement Protocol (TWAMP) server feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause the affected device to reload, resulting in a denial of service (DoS) condition. For Cisco IOS XR Software, this vulnerability could cause the ipsla_ippm_server process to reload unexpectedly if debugs are enabled. This vulnerability is due to out-of-bounds array access when processing specially crafted TWAMP control packets. An attacker could exploit this vulnerability by sending crafted TWAMP control packets to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Note: For Cisco IOS XR Software, only the ipsla_ippm_server process reloads unexpectedly and only when debugs are enabled. The vulnerability details for Cisco IOS XR Software are as follows: Security Impact Rating (SIR): Low CVSS Base Score: 3.7 CVSS Vector: CVSS:3.1/AV:N/AC:H/PR:N/UI:N/S:U/C:N/I:N/A:L | ||||
| CVE-2024-20311 | 1 Cisco | 3 Ios, Ios Xe, Ios Xe Software | 2025-07-30 | 8.6 High |
| A vulnerability in the Locator ID Separation Protocol (LISP) feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an affected device to reload. This vulnerability is due to the incorrect handling of LISP packets. An attacker could exploit this vulnerability by sending a crafted LISP packet to an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a denial of service (DoS) condition. Note: This vulnerability could be exploited over either IPv4 or IPv6 transport. | ||||
| CVE-2024-20307 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-30 | 6.8 Medium |
| A vulnerability in the IKEv1 fragmentation code of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a heap overflow, resulting in an affected device reloading. This vulnerability exists because crafted, fragmented IKEv1 packets are not properly reassembled. An attacker could exploit this vulnerability by sending crafted UDP packets to an affected system. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Note: Only traffic that is directed to the affected system can be used to exploit this vulnerability. This vulnerability can be triggered by IPv4 and IPv6 traffic. | ||||
| CVE-2004-1464 | 1 Cisco | 1 Ios | 2025-07-30 | 5.9 Medium |
| Cisco IOS 12.2(15) and earlier allows remote attackers to cause a denial of service (refused VTY (virtual terminal) connections), via a crafted TCP connection to the Telnet or reverse Telnet port. | ||||
| CVE-2016-6415 | 1 Cisco | 3 Ios, Ios Xe, Ios Xr | 2025-07-30 | 7.5 High |
| The server IKEv1 implementation in Cisco IOS 12.2 through 12.4 and 15.0 through 15.6, IOS XE through 3.18S, IOS XR 4.3.x and 5.0.x through 5.2.x, and PIX before 7.0 allows remote attackers to obtain sensitive information from device memory via a Security Association (SA) negotiation request, aka Bug IDs CSCvb29204 and CSCvb36055 or BENIGNCERTAIN. | ||||
| CVE-2017-3881 | 1 Cisco | 323 Catalyst 2350-48td-s, Catalyst 2350-48td-sd, Catalyst 2360-48td-s and 320 more | 2025-07-30 | 9.8 Critical |
| A vulnerability in the Cisco Cluster Management Protocol (CMP) processing code in Cisco IOS and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a reload of an affected device or remotely execute code with elevated privileges. The Cluster Management Protocol utilizes Telnet internally as a signaling and command protocol between cluster members. The vulnerability is due to the combination of two factors: (1) the failure to restrict the use of CMP-specific Telnet options only to internal, local communications between cluster members and instead accept and process such options over any Telnet connection to an affected device; and (2) the incorrect processing of malformed CMP-specific Telnet options. An attacker could exploit this vulnerability by sending malformed CMP-specific Telnet options while establishing a Telnet session with an affected Cisco device configured to accept Telnet connections. An exploit could allow an attacker to execute arbitrary code and obtain full control of the device or cause a reload of the affected device. This affects Catalyst switches, Embedded Service 2020 switches, Enhanced Layer 2 EtherSwitch Service Module, Enhanced Layer 2/3 EtherSwitch Service Module, Gigabit Ethernet Switch Module (CGESM) for HP, IE Industrial Ethernet switches, ME 4924-10GE switch, RF Gateway 10, and SM-X Layer 2/3 EtherSwitch Service Module. Cisco Bug IDs: CSCvd48893. | ||||
| CVE-2017-6663 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-30 | 6.5 Medium |
| A vulnerability in the Autonomic Networking feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, adjacent attacker to cause autonomic nodes of an affected system to reload, resulting in a denial of service (DoS) condition. More Information: CSCvd88936. Known Affected Releases: Denali-16.2.1 Denali-16.3.1. | ||||