Total
505 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2024-50284 | 1 Linux | 1 Linux Kernel | 2025-11-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ksmbd: Fix the missing xa_store error check xa_store() can fail, it return xa_err(-EINVAL) if the entry cannot be stored in an XArray, or xa_err(-ENOMEM) if memory allocation failed, so check error for xa_store() to fix it. | ||||
| CVE-2024-50196 | 1 Linux | 1 Linux Kernel | 2025-11-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: pinctrl: ocelot: fix system hang on level based interrupts The current implementation only calls chained_irq_enter() and chained_irq_exit() if it detects pending interrupts. ``` for (i = 0; i < info->stride; i++) { uregmap_read(info->map, id_reg + 4 * i, ®); if (!reg) continue; chained_irq_enter(parent_chip, desc); ``` However, in case of GPIO pin configured in level mode and the parent controller configured in edge mode, GPIO interrupt might be lowered by the hardware. In the result, if the interrupt is short enough, the parent interrupt is still pending while the GPIO interrupt is cleared; chained_irq_enter() never gets called and the system hangs trying to service the parent interrupt. Moving chained_irq_enter() and chained_irq_exit() outside the for loop ensures that they are called even when GPIO interrupt is lowered by the hardware. The similar code with chained_irq_enter() / chained_irq_exit() functions wrapping interrupt checking loop may be found in many other drivers: ``` grep -r -A 10 chained_irq_enter drivers/pinctrl ``` | ||||
| CVE-2024-50195 | 1 Linux | 1 Linux Kernel | 2025-11-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: posix-clock: Fix missing timespec64 check in pc_clock_settime() As Andrew pointed out, it will make sense that the PTP core checked timespec64 struct's tv_sec and tv_nsec range before calling ptp->info->settime64(). As the man manual of clock_settime() said, if tp.tv_sec is negative or tp.tv_nsec is outside the range [0..999,999,999], it should return EINVAL, which include dynamic clocks which handles PTP clock, and the condition is consistent with timespec64_valid(). As Thomas suggested, timespec64_valid() only check the timespec is valid, but not ensure that the time is in a valid range, so check it ahead using timespec64_valid_strict() in pc_clock_settime() and return -EINVAL if not valid. There are some drivers that use tp->tv_sec and tp->tv_nsec directly to write registers without validity checks and assume that the higher layer has checked it, which is dangerous and will benefit from this, such as hclge_ptp_settime(), igb_ptp_settime_i210(), _rcar_gen4_ptp_settime(), and some drivers can remove the checks of itself. | ||||
| CVE-2024-50184 | 1 Linux | 1 Linux Kernel | 2025-11-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: virtio_pmem: Check device status before requesting flush If a pmem device is in a bad status, the driver side could wait for host ack forever in virtio_pmem_flush(), causing the system to hang. So add a status check in the beginning of virtio_pmem_flush() to return early if the device is not activated. | ||||
| CVE-2024-50096 | 1 Linux | 1 Linux Kernel | 2025-11-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: nouveau/dmem: Fix vulnerability in migrate_to_ram upon copy error The `nouveau_dmem_copy_one` function ensures that the copy push command is sent to the device firmware but does not track whether it was executed successfully. In the case of a copy error (e.g., firmware or hardware failure), the copy push command will be sent via the firmware channel, and `nouveau_dmem_copy_one` will likely report success, leading to the `migrate_to_ram` function returning a dirty HIGH_USER page to the user. This can result in a security vulnerability, as a HIGH_USER page that may contain sensitive or corrupted data could be returned to the user. To prevent this vulnerability, we allocate a zero page. Thus, in case of an error, a non-dirty (zero) page will be returned to the user. | ||||
| CVE-2024-47727 | 1 Linux | 1 Linux Kernel | 2025-11-03 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: x86/tdx: Fix "in-kernel MMIO" check TDX only supports kernel-initiated MMIO operations. The handle_mmio() function checks if the #VE exception occurred in the kernel and rejects the operation if it did not. However, userspace can deceive the kernel into performing MMIO on its behalf. For example, if userspace can point a syscall to an MMIO address, syscall does get_user() or put_user() on it, triggering MMIO #VE. The kernel will treat the #VE as in-kernel MMIO. Ensure that the target MMIO address is within the kernel before decoding instruction. | ||||
| CVE-2024-47672 | 1 Linux | 1 Linux Kernel | 2025-11-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: don't wait for tx queues if firmware is dead There is a WARNING in iwl_trans_wait_tx_queues_empty() (that was recently converted from just a message), that can be hit if we wait for TX queues to become empty after firmware died. Clearly, we can't expect anything from the firmware after it's declared dead. Don't call iwl_trans_wait_tx_queues_empty() in this case. While it could be a good idea to stop the flow earlier, the flush functions do some maintenance work that is not related to the firmware, so keep that part of the code running even when the firmware is not running. [edit commit message] | ||||
| CVE-2024-46848 | 1 Linux | 1 Linux Kernel | 2025-11-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: perf/x86/intel: Limit the period on Haswell Running the ltp test cve-2015-3290 concurrently reports the following warnings. perfevents: irq loop stuck! WARNING: CPU: 31 PID: 32438 at arch/x86/events/intel/core.c:3174 intel_pmu_handle_irq+0x285/0x370 Call Trace: <NMI> ? __warn+0xa4/0x220 ? intel_pmu_handle_irq+0x285/0x370 ? __report_bug+0x123/0x130 ? intel_pmu_handle_irq+0x285/0x370 ? __report_bug+0x123/0x130 ? intel_pmu_handle_irq+0x285/0x370 ? report_bug+0x3e/0xa0 ? handle_bug+0x3c/0x70 ? exc_invalid_op+0x18/0x50 ? asm_exc_invalid_op+0x1a/0x20 ? irq_work_claim+0x1e/0x40 ? intel_pmu_handle_irq+0x285/0x370 perf_event_nmi_handler+0x3d/0x60 nmi_handle+0x104/0x330 Thanks to Thomas Gleixner's analysis, the issue is caused by the low initial period (1) of the frequency estimation algorithm, which triggers the defects of the HW, specifically erratum HSW11 and HSW143. (For the details, please refer https://lore.kernel.org/lkml/87plq9l5d2.ffs@tglx/) The HSW11 requires a period larger than 100 for the INST_RETIRED.ALL event, but the initial period in the freq mode is 1. The erratum is the same as the BDM11, which has been supported in the kernel. A minimum period of 128 is enforced as well on HSW. HSW143 is regarding that the fixed counter 1 may overcount 32 with the Hyper-Threading is enabled. However, based on the test, the hardware has more issues than it tells. Besides the fixed counter 1, the message 'interrupt took too long' can be observed on any counter which was armed with a period < 32 and two events expired in the same NMI. A minimum period of 32 is enforced for the rest of the events. The recommended workaround code of the HSW143 is not implemented. Because it only addresses the issue for the fixed counter. It brings extra overhead through extra MSR writing. No related overcounting issue has been reported so far. | ||||
| CVE-2024-44948 | 1 Linux | 1 Linux Kernel | 2025-11-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: x86/mtrr: Check if fixed MTRRs exist before saving them MTRRs have an obsolete fixed variant for fine grained caching control of the 640K-1MB region that uses separate MSRs. This fixed variant has a separate capability bit in the MTRR capability MSR. So far all x86 CPUs which support MTRR have this separate bit set, so it went unnoticed that mtrr_save_state() does not check the capability bit before accessing the fixed MTRR MSRs. Though on a CPU that does not support the fixed MTRR capability this results in a #GP. The #GP itself is harmless because the RDMSR fault is handled gracefully, but results in a WARN_ON(). Add the missing capability check to prevent this. | ||||
| CVE-2024-44235 | 1 Apple | 2 Ipados, Iphone Os | 2025-11-03 | 4.6 Medium |
| The issue was addressed with improved checks. This issue is fixed in iOS 18.1 and iPadOS 18.1. An attacker may be able to view restricted content from the lock screen. | ||||
| CVE-2024-42284 | 2 Linux, Redhat | 3 Linux Kernel, Enterprise Linux, Rhel Eus | 2025-11-03 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: tipc: Return non-zero value from tipc_udp_addr2str() on error tipc_udp_addr2str() should return non-zero value if the UDP media address is invalid. Otherwise, a buffer overflow access can occur in tipc_media_addr_printf(). Fix this by returning 1 on an invalid UDP media address. | ||||
| CVE-2024-42224 | 1 Linux | 1 Linux Kernel | 2025-11-03 | 6.1 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net: dsa: mv88e6xxx: Correct check for empty list Since commit a3c53be55c95 ("net: dsa: mv88e6xxx: Support multiple MDIO busses") mv88e6xxx_default_mdio_bus() has checked that the return value of list_first_entry() is non-NULL. This appears to be intended to guard against the list chip->mdios being empty. However, it is not the correct check as the implementation of list_first_entry is not designed to return NULL for empty lists. Instead, use list_first_entry_or_null() which does return NULL if the list is empty. Flagged by Smatch. Compile tested only. | ||||
| CVE-2024-42160 | 1 Linux | 1 Linux Kernel | 2025-11-03 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: f2fs: check validation of fault attrs in f2fs_build_fault_attr() - It missed to check validation of fault attrs in parse_options(), let's fix to add check condition in f2fs_build_fault_attr(). - Use f2fs_build_fault_attr() in __sbi_store() to clean up code. | ||||
| CVE-2024-42159 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2025-11-03 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: scsi: mpi3mr: Sanitise num_phys Information is stored in mr_sas_port->phy_mask, values larger then size of this field shouldn't be allowed. | ||||
| CVE-2024-42154 | 2 Linux, Redhat | 3 Linux Kernel, Enterprise Linux, Rhel Eus | 2025-11-03 | 4.4 Medium |
| In the Linux kernel, the following vulnerability has been resolved: tcp_metrics: validate source addr length I don't see anything checking that TCP_METRICS_ATTR_SADDR_IPV4 is at least 4 bytes long, and the policy doesn't have an entry for this attribute at all (neither does it for IPv6 but v6 is manually validated). | ||||
| CVE-2024-40968 | 1 Linux | 1 Linux Kernel | 2025-11-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: MIPS: Octeon: Add PCIe link status check The standard PCIe configuration read-write interface is used to access the configuration space of the peripheral PCIe devices of the mips processor after the PCIe link surprise down, it can generate kernel panic caused by "Data bus error". So it is necessary to add PCIe link status check for system protection. When the PCIe link is down or in training, assigning a value of 0 to the configuration address can prevent read-write behavior to the configuration space of peripheral PCIe devices, thereby preventing kernel panic. | ||||
| CVE-2024-40963 | 1 Linux | 1 Linux Kernel | 2025-11-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: mips: bmips: BCM6358: make sure CBR is correctly set It was discovered that some device have CBR address set to 0 causing kernel panic when arch_sync_dma_for_cpu_all is called. This was notice in situation where the system is booted from TP1 and BMIPS_GET_CBR() returns 0 instead of a valid address and !!(read_c0_brcm_cmt_local() & (1 << 31)); not failing. The current check whether RAC flush should be disabled or not are not enough hence lets check if CBR is a valid address or not. | ||||
| CVE-2024-20506 | 1 Clamav | 1 Clamav | 2025-11-03 | 6.1 Medium |
| A vulnerability in the ClamD service module of Clam AntiVirus (ClamAV) versions 1.4.0, 1.3.2 and prior versions, all 1.2.x versions, 1.0.6 and prior versions, all 0.105.x versions, all 0.104.x versions, and 0.103.11 and all prior versions could allow an authenticated, local attacker to corrupt critical system files. The vulnerability is due to allowing the ClamD process to write to its log file while privileged without checking if the logfile has been replaced with a symbolic link. An attacker could exploit this vulnerability if they replace the ClamD log file with a symlink to a critical system file and then find a way to restart the ClamD process. An exploit could allow the attacker to corrupt a critical system file by appending ClamD log messages after restart. | ||||
| CVE-2023-5678 | 2 Openssl, Redhat | 5 Openssl, Enterprise Linux, Jboss Core Services and 2 more | 2025-11-03 | 5.3 Medium |
| Issue summary: Generating excessively long X9.42 DH keys or checking excessively long X9.42 DH keys or parameters may be very slow. Impact summary: Applications that use the functions DH_generate_key() to generate an X9.42 DH key may experience long delays. Likewise, applications that use DH_check_pub_key(), DH_check_pub_key_ex() or EVP_PKEY_public_check() to check an X9.42 DH key or X9.42 DH parameters may experience long delays. Where the key or parameters that are being checked have been obtained from an untrusted source this may lead to a Denial of Service. While DH_check() performs all the necessary checks (as of CVE-2023-3817), DH_check_pub_key() doesn't make any of these checks, and is therefore vulnerable for excessively large P and Q parameters. Likewise, while DH_generate_key() performs a check for an excessively large P, it doesn't check for an excessively large Q. An application that calls DH_generate_key() or DH_check_pub_key() and supplies a key or parameters obtained from an untrusted source could be vulnerable to a Denial of Service attack. DH_generate_key() and DH_check_pub_key() are also called by a number of other OpenSSL functions. An application calling any of those other functions may similarly be affected. The other functions affected by this are DH_check_pub_key_ex(), EVP_PKEY_public_check(), and EVP_PKEY_generate(). Also vulnerable are the OpenSSL pkey command line application when using the "-pubcheck" option, as well as the OpenSSL genpkey command line application. The OpenSSL SSL/TLS implementation is not affected by this issue. The OpenSSL 3.0 and 3.1 FIPS providers are not affected by this issue. | ||||
| CVE-2023-32726 | 1 Zabbix | 1 Zabbix-agent | 2025-11-03 | 3.9 Low |
| The vulnerability is caused by improper check for check if RDLENGTH does not overflow the buffer in response from DNS server. | ||||