Total
12282 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2024-42092 | 2025-05-04 | 4.1 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: gpio: davinci: Validate the obtained number of IRQs Value of pdata->gpio_unbanked is taken from Device Tree. In case of broken DT due to any error this value can be any. Without this value validation there can be out of chips->irqs array boundaries access in davinci_gpio_probe(). Validate the obtained nirq value so that it won't exceed the maximum number of IRQs per bank. Found by Linux Verification Center (linuxtesting.org) with SVACE. | ||||
| CVE-2024-42064 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Skip pipe if the pipe idx not set properly [why] Driver crashes when pipe idx not set properly [how] Add code to skip the pipe that idx not set properly | ||||
| CVE-2024-41091 | 1 Redhat | 5 Enterprise Linux, Rhel Aus, Rhel E4s and 2 more | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: tun: add missing verification for short frame The cited commit missed to check against the validity of the frame length in the tun_xdp_one() path, which could cause a corrupted skb to be sent downstack. Even before the skb is transmitted, the tun_xdp_one-->eth_type_trans() may access the Ethernet header although it can be less than ETH_HLEN. Once transmitted, this could either cause out-of-bound access beyond the actual length, or confuse the underlayer with incorrect or inconsistent header length in the skb metadata. In the alternative path, tun_get_user() already prohibits short frame which has the length less than Ethernet header size from being transmitted for IFF_TAP. This is to drop any frame shorter than the Ethernet header size just like how tun_get_user() does. CVE: CVE-2024-41091 | ||||
| CVE-2024-41090 | 1 Redhat | 5 Enterprise Linux, Rhel Aus, Rhel E4s and 2 more | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: tap: add missing verification for short frame The cited commit missed to check against the validity of the frame length in the tap_get_user_xdp() path, which could cause a corrupted skb to be sent downstack. Even before the skb is transmitted, the tap_get_user_xdp()-->skb_set_network_header() may assume the size is more than ETH_HLEN. Once transmitted, this could either cause out-of-bound access beyond the actual length, or confuse the underlayer with incorrect or inconsistent header length in the skb metadata. In the alternative path, tap_get_user() already prohibits short frame which has the length less than Ethernet header size from being transmitted. This is to drop any frame shorter than the Ethernet header size just like how tap_get_user() does. CVE: CVE-2024-41090 | ||||
| CVE-2024-41060 | 2 Linux, Redhat | 3 Linux Kernel, Enterprise Linux, Rhel Eus | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: drm/radeon: check bo_va->bo is non-NULL before using it The call to radeon_vm_clear_freed might clear bo_va->bo, so we have to check it before dereferencing it. | ||||
| CVE-2024-41059 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: hfsplus: fix uninit-value in copy_name [syzbot reported] BUG: KMSAN: uninit-value in sized_strscpy+0xc4/0x160 sized_strscpy+0xc4/0x160 copy_name+0x2af/0x320 fs/hfsplus/xattr.c:411 hfsplus_listxattr+0x11e9/0x1a50 fs/hfsplus/xattr.c:750 vfs_listxattr fs/xattr.c:493 [inline] listxattr+0x1f3/0x6b0 fs/xattr.c:840 path_listxattr fs/xattr.c:864 [inline] __do_sys_listxattr fs/xattr.c:876 [inline] __se_sys_listxattr fs/xattr.c:873 [inline] __x64_sys_listxattr+0x16b/0x2f0 fs/xattr.c:873 x64_sys_call+0x2ba0/0x3b50 arch/x86/include/generated/asm/syscalls_64.h:195 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Uninit was created at: slab_post_alloc_hook mm/slub.c:3877 [inline] slab_alloc_node mm/slub.c:3918 [inline] kmalloc_trace+0x57b/0xbe0 mm/slub.c:4065 kmalloc include/linux/slab.h:628 [inline] hfsplus_listxattr+0x4cc/0x1a50 fs/hfsplus/xattr.c:699 vfs_listxattr fs/xattr.c:493 [inline] listxattr+0x1f3/0x6b0 fs/xattr.c:840 path_listxattr fs/xattr.c:864 [inline] __do_sys_listxattr fs/xattr.c:876 [inline] __se_sys_listxattr fs/xattr.c:873 [inline] __x64_sys_listxattr+0x16b/0x2f0 fs/xattr.c:873 x64_sys_call+0x2ba0/0x3b50 arch/x86/include/generated/asm/syscalls_64.h:195 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f [Fix] When allocating memory to strbuf, initialize memory to 0. | ||||
| CVE-2024-41044 | 1 Redhat | 2 Enterprise Linux, Rhel Eus | 2025-05-04 | 4.9 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ppp: reject claimed-as-LCP but actually malformed packets Since 'ppp_async_encode()' assumes valid LCP packets (with code from 1 to 7 inclusive), add 'ppp_check_packet()' to ensure that LCP packet has an actual body beyond PPP_LCP header bytes, and reject claimed-as-LCP but actually malformed data otherwise. | ||||
| CVE-2024-41017 | 2025-05-04 | 5.5 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: jfs: don't walk off the end of ealist Add a check before visiting the members of ea to make sure each ea stays within the ealist. | ||||
| CVE-2024-41016 | 2025-05-04 | 5.5 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: ocfs2: strict bound check before memcmp in ocfs2_xattr_find_entry() xattr in ocfs2 maybe 'non-indexed', which saved with additional space requested. It's better to check if the memory is out of bound before memcmp, although this possibility mainly comes from crafted poisonous images. | ||||
| CVE-2024-41004 | 2025-05-04 | 4.4 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: tracing: Build event generation tests only as modules The kprobes and synth event generation test modules add events and lock (get a reference) those event file reference in module init function, and unlock and delete it in module exit function. This is because those are designed for playing as modules. If we make those modules as built-in, those events are left locked in the kernel, and never be removed. This causes kprobe event self-test failure as below. [ 97.349708] ------------[ cut here ]------------ [ 97.353453] WARNING: CPU: 3 PID: 1 at kernel/trace/trace_kprobe.c:2133 kprobe_trace_self_tests_init+0x3f1/0x480 [ 97.357106] Modules linked in: [ 97.358488] CPU: 3 PID: 1 Comm: swapper/0 Not tainted 6.9.0-g699646734ab5-dirty #14 [ 97.361556] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 [ 97.363880] RIP: 0010:kprobe_trace_self_tests_init+0x3f1/0x480 [ 97.365538] Code: a8 24 08 82 e9 ae fd ff ff 90 0f 0b 90 48 c7 c7 e5 aa 0b 82 e9 ee fc ff ff 90 0f 0b 90 48 c7 c7 2d 61 06 82 e9 8e fd ff ff 90 <0f> 0b 90 48 c7 c7 33 0b 0c 82 89 c6 e8 6e 03 1f ff 41 ff c7 e9 90 [ 97.370429] RSP: 0000:ffffc90000013b50 EFLAGS: 00010286 [ 97.371852] RAX: 00000000fffffff0 RBX: ffff888005919c00 RCX: 0000000000000000 [ 97.373829] RDX: ffff888003f40000 RSI: ffffffff8236a598 RDI: ffff888003f40a68 [ 97.375715] RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000 [ 97.377675] R10: ffffffff811c9ae5 R11: ffffffff8120c4e0 R12: 0000000000000000 [ 97.379591] R13: 0000000000000001 R14: 0000000000000015 R15: 0000000000000000 [ 97.381536] FS: 0000000000000000(0000) GS:ffff88807dcc0000(0000) knlGS:0000000000000000 [ 97.383813] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 97.385449] CR2: 0000000000000000 CR3: 0000000002244000 CR4: 00000000000006b0 [ 97.387347] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 97.389277] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 97.391196] Call Trace: [ 97.391967] <TASK> [ 97.392647] ? __warn+0xcc/0x180 [ 97.393640] ? kprobe_trace_self_tests_init+0x3f1/0x480 [ 97.395181] ? report_bug+0xbd/0x150 [ 97.396234] ? handle_bug+0x3e/0x60 [ 97.397311] ? exc_invalid_op+0x1a/0x50 [ 97.398434] ? asm_exc_invalid_op+0x1a/0x20 [ 97.399652] ? trace_kprobe_is_busy+0x20/0x20 [ 97.400904] ? tracing_reset_all_online_cpus+0x15/0x90 [ 97.402304] ? kprobe_trace_self_tests_init+0x3f1/0x480 [ 97.403773] ? init_kprobe_trace+0x50/0x50 [ 97.404972] do_one_initcall+0x112/0x240 [ 97.406113] do_initcall_level+0x95/0xb0 [ 97.407286] ? kernel_init+0x1a/0x1a0 [ 97.408401] do_initcalls+0x3f/0x70 [ 97.409452] kernel_init_freeable+0x16f/0x1e0 [ 97.410662] ? rest_init+0x1f0/0x1f0 [ 97.411738] kernel_init+0x1a/0x1a0 [ 97.412788] ret_from_fork+0x39/0x50 [ 97.413817] ? rest_init+0x1f0/0x1f0 [ 97.414844] ret_from_fork_asm+0x11/0x20 [ 97.416285] </TASK> [ 97.417134] irq event stamp: 13437323 [ 97.418376] hardirqs last enabled at (13437337): [<ffffffff8110bc0c>] console_unlock+0x11c/0x150 [ 97.421285] hardirqs last disabled at (13437370): [<ffffffff8110bbf1>] console_unlock+0x101/0x150 [ 97.423838] softirqs last enabled at (13437366): [<ffffffff8108e17f>] handle_softirqs+0x23f/0x2a0 [ 97.426450] softirqs last disabled at (13437393): [<ffffffff8108e346>] __irq_exit_rcu+0x66/0xd0 [ 97.428850] ---[ end trace 0000000000000000 ]--- And also, since we can not cleanup dynamic_event file, ftracetest are failed too. To avoid these issues, build these tests only as modules. | ||||
| CVE-2024-40992 | 2025-05-04 | 4.4 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: RDMA/rxe: Fix responder length checking for UD request packets According to the IBA specification: If a UD request packet is detected with an invalid length, the request shall be an invalid request and it shall be silently dropped by the responder. The responder then waits for a new request packet. commit 689c5421bfe0 ("RDMA/rxe: Fix incorrect responder length checking") defers responder length check for UD QPs in function `copy_data`. But it introduces a regression issue for UD QPs. When the packet size is too large to fit in the receive buffer. `copy_data` will return error code -EINVAL. Then `send_data_in` will return RESPST_ERR_MALFORMED_WQE. UD QP will transfer into ERROR state. | ||||
| CVE-2024-40990 | 2025-05-04 | 4.2 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Add check for srq max_sge attribute max_sge attribute is passed by the user, and is inserted and used unchecked, so verify that the value doesn't exceed maximum allowed value before using it. | ||||
| CVE-2024-40930 | 1 Redhat | 1 Enterprise Linux | 2025-05-04 | 5.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: validate HE operation element parsing Validate that the HE operation element has the correct length before parsing it. | ||||
| CVE-2024-40917 | 2025-05-04 | 5.5 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: memblock: make memblock_set_node() also warn about use of MAX_NUMNODES On an (old) x86 system with SRAT just covering space above 4Gb: ACPI: SRAT: Node 0 PXM 0 [mem 0x100000000-0xfffffffff] hotplug the commit referenced below leads to this NUMA configuration no longer being refused by a CONFIG_NUMA=y kernel (previously NUMA: nodes only cover 6144MB of your 8185MB e820 RAM. Not used. No NUMA configuration found Faking a node at [mem 0x0000000000000000-0x000000027fffffff] was seen in the log directly after the message quoted above), because of memblock_validate_numa_coverage() checking for NUMA_NO_NODE (only). This in turn led to memblock_alloc_range_nid()'s warning about MAX_NUMNODES triggering, followed by a NULL deref in memmap_init() when trying to access node 64's (NODE_SHIFT=6) node data. To compensate said change, make memblock_set_node() warn on and adjust a passed in value of MAX_NUMNODES, just like various other functions already do. | ||||
| CVE-2024-39505 | 2025-05-04 | 4.4 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: drm/komeda: check for error-valued pointer komeda_pipeline_get_state() may return an error-valued pointer, thus check the pointer for negative or null value before dereferencing. | ||||
| CVE-2024-38636 | 2025-05-04 | 5.5 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: f2fs: multidev: fix to recognize valid zero block address As reported by Yi Zhang in mailing list [1], kernel warning was catched during zbd/010 test as below: ./check zbd/010 zbd/010 (test gap zone support with F2FS) [failed] runtime ... 3.752s something found in dmesg: [ 4378.146781] run blktests zbd/010 at 2024-02-18 11:31:13 [ 4378.192349] null_blk: module loaded [ 4378.209860] null_blk: disk nullb0 created [ 4378.413285] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 4378.422334] scsi host15: scsi_debug: version 0191 [20210520] dev_size_mb=1024, opts=0x0, submit_queues=1, statistics=0 [ 4378.434922] scsi 15:0:0:0: Direct-Access-ZBC Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 4378.443343] scsi 15:0:0:0: Power-on or device reset occurred [ 4378.449371] sd 15:0:0:0: Attached scsi generic sg5 type 20 [ 4378.449418] sd 15:0:0:0: [sdf] Host-managed zoned block device ... (See '/mnt/tests/gitlab.com/api/v4/projects/19168116/repository/archive.zip/storage/blktests/blk/blktests/results/nodev/zbd/010.dmesg' WARNING: CPU: 22 PID: 44011 at fs/iomap/iter.c:51 CPU: 22 PID: 44011 Comm: fio Not tainted 6.8.0-rc3+ #1 RIP: 0010:iomap_iter+0x32b/0x350 Call Trace: <TASK> __iomap_dio_rw+0x1df/0x830 f2fs_file_read_iter+0x156/0x3d0 [f2fs] aio_read+0x138/0x210 io_submit_one+0x188/0x8c0 __x64_sys_io_submit+0x8c/0x1a0 do_syscall_64+0x86/0x170 entry_SYSCALL_64_after_hwframe+0x6e/0x76 Shinichiro Kawasaki helps to analyse this issue and proposes a potential fixing patch in [2]. Quoted from reply of Shinichiro Kawasaki: "I confirmed that the trigger commit is dbf8e63f48af as Yi reported. I took a look in the commit, but it looks fine to me. So I thought the cause is not in the commit diff. I found the WARN is printed when the f2fs is set up with multiple devices, and read requests are mapped to the very first block of the second device in the direct read path. In this case, f2fs_map_blocks() and f2fs_map_blocks_cached() modify map->m_pblk as the physical block address from each block device. It becomes zero when it is mapped to the first block of the device. However, f2fs_iomap_begin() assumes that map->m_pblk is the physical block address of the whole f2fs, across the all block devices. It compares map->m_pblk against NULL_ADDR == 0, then go into the unexpected branch and sets the invalid iomap->length. The WARN catches the invalid iomap->length. This WARN is printed even for non-zoned block devices, by following steps. - Create two (non-zoned) null_blk devices memory backed with 128MB size each: nullb0 and nullb1. # mkfs.f2fs /dev/nullb0 -c /dev/nullb1 # mount -t f2fs /dev/nullb0 "${mount_dir}" # dd if=/dev/zero of="${mount_dir}/test.dat" bs=1M count=192 # dd if="${mount_dir}/test.dat" of=/dev/null bs=1M count=192 iflag=direct ..." So, the root cause of this issue is: when multi-devices feature is on, f2fs_map_blocks() may return zero blkaddr in non-primary device, which is a verified valid block address, however, f2fs_iomap_begin() treats it as an invalid block address, and then it triggers the warning in iomap framework code. Finally, as discussed, we decide to use a more simple and direct way that checking (map.m_flags & F2FS_MAP_MAPPED) condition instead of (map.m_pblk != NULL_ADDR) to fix this issue. Thanks a lot for the effort of Yi Zhang and Shinichiro Kawasaki on this issue. [1] https://lore.kernel.org/linux-f2fs-devel/CAHj4cs-kfojYC9i0G73PRkYzcxCTex=-vugRFeP40g_URGvnfQ@mail.gmail.com/ [2] https://lore.kernel.org/linux-f2fs-devel/gngdj77k4picagsfdtiaa7gpgnup6fsgwzsltx6milmhegmjff@iax2n4wvrqye/ | ||||
| CVE-2024-38626 | 2025-05-04 | 5.5 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: fuse: clear FR_SENT when re-adding requests into pending list The following warning was reported by lee bruce: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 8264 at fs/fuse/dev.c:300 fuse_request_end+0x685/0x7e0 fs/fuse/dev.c:300 Modules linked in: CPU: 0 PID: 8264 Comm: ab2 Not tainted 6.9.0-rc7 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) RIP: 0010:fuse_request_end+0x685/0x7e0 fs/fuse/dev.c:300 ...... Call Trace: <TASK> fuse_dev_do_read.constprop.0+0xd36/0x1dd0 fs/fuse/dev.c:1334 fuse_dev_read+0x166/0x200 fs/fuse/dev.c:1367 call_read_iter include/linux/fs.h:2104 [inline] new_sync_read fs/read_write.c:395 [inline] vfs_read+0x85b/0xba0 fs/read_write.c:476 ksys_read+0x12f/0x260 fs/read_write.c:619 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xce/0x260 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f ...... </TASK> The warning is due to the FUSE_NOTIFY_RESEND notify sent by the write() syscall in the reproducer program and it happens as follows: (1) calls fuse_dev_read() to read the INIT request The read succeeds. During the read, bit FR_SENT will be set on the request. (2) calls fuse_dev_write() to send an USE_NOTIFY_RESEND notify The resend notify will resend all processing requests, so the INIT request is moved from processing list to pending list again. (3) calls fuse_dev_read() with an invalid output address fuse_dev_read() will try to copy the same INIT request to the output address, but it will fail due to the invalid address, so the INIT request is ended and triggers the warning in fuse_request_end(). Fix it by clearing FR_SENT when re-adding requests into pending list. | ||||
| CVE-2024-38604 | 1 Redhat | 1 Enterprise Linux | 2025-05-04 | 4.4 Medium |
| In the Linux kernel, the following vulnerability has been resolved: block: refine the EOF check in blkdev_iomap_begin blkdev_iomap_begin rounds down the offset to the logical block size before stashing it in iomap->offset and checking that it still is inside the inode size. Check the i_size check to the raw pos value so that we don't try a zero size write if iter->pos is unaligned. | ||||
| CVE-2024-38567 | 2025-05-04 | 4.4 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: wifi: carl9170: add a proper sanity check for endpoints Syzkaller reports [1] hitting a warning which is caused by presence of a wrong endpoint type at the URB sumbitting stage. While there was a check for a specific 4th endpoint, since it can switch types between bulk and interrupt, other endpoints are trusted implicitly. Similar warning is triggered in a couple of other syzbot issues [2]. Fix the issue by doing a comprehensive check of all endpoints taking into account difference between high- and full-speed configuration. [1] Syzkaller report: ... WARNING: CPU: 0 PID: 4721 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504 ... Call Trace: <TASK> carl9170_usb_send_rx_irq_urb+0x273/0x340 drivers/net/wireless/ath/carl9170/usb.c:504 carl9170_usb_init_device drivers/net/wireless/ath/carl9170/usb.c:939 [inline] carl9170_usb_firmware_finish drivers/net/wireless/ath/carl9170/usb.c:999 [inline] carl9170_usb_firmware_step2+0x175/0x240 drivers/net/wireless/ath/carl9170/usb.c:1028 request_firmware_work_func+0x130/0x240 drivers/base/firmware_loader/main.c:1107 process_one_work+0x9bf/0x1710 kernel/workqueue.c:2289 worker_thread+0x669/0x1090 kernel/workqueue.c:2436 kthread+0x2e8/0x3a0 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308 </TASK> [2] Related syzkaller crashes: | ||||
| CVE-2024-38566 | 2025-05-04 | 4.4 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: bpf: Fix verifier assumptions about socket->sk The verifier assumes that 'sk' field in 'struct socket' is valid and non-NULL when 'socket' pointer itself is trusted and non-NULL. That may not be the case when socket was just created and passed to LSM socket_accept hook. Fix this verifier assumption and adjust tests. | ||||