Total
33659 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2025-38432 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net: netpoll: Initialize UDP checksum field before checksumming commit f1fce08e63fe ("netpoll: Eliminate redundant assignment") removed the initialization of the UDP checksum, which was wrong and broke netpoll IPv6 transmission due to bad checksumming. udph->check needs to be set before calling csum_ipv6_magic(). | ||||
| CVE-2025-38435 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: riscv: vector: Fix context save/restore with xtheadvector Previously only v0-v7 were correctly saved/restored, and the context of v8-v31 are damanged. Correctly save/restore v8-v31 to avoid breaking userspace. | ||||
| CVE-2025-38434 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: Revert "riscv: Define TASK_SIZE_MAX for __access_ok()" This reverts commit ad5643cf2f69 ("riscv: Define TASK_SIZE_MAX for __access_ok()"). This commit changes TASK_SIZE_MAX to be LONG_MAX to optimize access_ok(), because the previous TASK_SIZE_MAX (default to TASK_SIZE) requires some computation. The reasoning was that all user addresses are less than LONG_MAX, and all kernel addresses are greater than LONG_MAX. Therefore access_ok() can filter kernel addresses. Addresses between TASK_SIZE and LONG_MAX are not valid user addresses, but access_ok() let them pass. That was thought to be okay, because they are not valid addresses at hardware level. Unfortunately, one case is missed: get_user_pages_fast() happily accepts addresses between TASK_SIZE and LONG_MAX. futex(), for instance, uses get_user_pages_fast(). This causes the problem reported by Robert [1]. Therefore, revert this commit. TASK_SIZE_MAX is changed to the default: TASK_SIZE. This unfortunately reduces performance, because TASK_SIZE is more expensive to compute compared to LONG_MAX. But correctness first, we can think about optimization later, if required. | ||||
| CVE-2025-38469 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: KVM: x86/xen: Fix cleanup logic in emulation of Xen schedop poll hypercalls kvm_xen_schedop_poll does a kmalloc_array() when a VM polls the host for more than one event channel potr (nr_ports > 1). After the kmalloc_array(), the error paths need to go through the "out" label, but the call to kvm_read_guest_virt() does not. [Adjusted commit message. - Paolo] | ||||
| CVE-2025-38453 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: io_uring/msg_ring: ensure io_kiocb freeing is deferred for RCU syzbot reports that defer/local task_work adding via msg_ring can hit a request that has been freed: CPU: 1 UID: 0 PID: 19356 Comm: iou-wrk-19354 Not tainted 6.16.0-rc4-syzkaller-00108-g17bbde2e1716 #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/07/2025 Call Trace: <TASK> dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:408 [inline] print_report+0xd2/0x2b0 mm/kasan/report.c:521 kasan_report+0x118/0x150 mm/kasan/report.c:634 io_req_local_work_add io_uring/io_uring.c:1184 [inline] __io_req_task_work_add+0x589/0x950 io_uring/io_uring.c:1252 io_msg_remote_post io_uring/msg_ring.c:103 [inline] io_msg_data_remote io_uring/msg_ring.c:133 [inline] __io_msg_ring_data+0x820/0xaa0 io_uring/msg_ring.c:151 io_msg_ring_data io_uring/msg_ring.c:173 [inline] io_msg_ring+0x134/0xa00 io_uring/msg_ring.c:314 __io_issue_sqe+0x17e/0x4b0 io_uring/io_uring.c:1739 io_issue_sqe+0x165/0xfd0 io_uring/io_uring.c:1762 io_wq_submit_work+0x6e9/0xb90 io_uring/io_uring.c:1874 io_worker_handle_work+0x7cd/0x1180 io_uring/io-wq.c:642 io_wq_worker+0x42f/0xeb0 io_uring/io-wq.c:696 ret_from_fork+0x3fc/0x770 arch/x86/kernel/process.c:148 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 </TASK> which is supposed to be safe with how requests are allocated. But msg ring requests alloc and free on their own, and hence must defer freeing to a sane time. Add an rcu_head and use kfree_rcu() in both spots where requests are freed. Only the one in io_msg_tw_complete() is strictly required as it has been visible on the other ring, but use it consistently in the other spot as well. This should not cause any other issues outside of KASAN rightfully complaining about it. | ||||
| CVE-2025-38496 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: dm-bufio: fix sched in atomic context If "try_verify_in_tasklet" is set for dm-verity, DM_BUFIO_CLIENT_NO_SLEEP is enabled for dm-bufio. However, when bufio tries to evict buffers, there is a chance to trigger scheduling in spin_lock_bh, the following warning is hit: BUG: sleeping function called from invalid context at drivers/md/dm-bufio.c:2745 in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 123, name: kworker/2:2 preempt_count: 201, expected: 0 RCU nest depth: 0, expected: 0 4 locks held by kworker/2:2/123: #0: ffff88800a2d1548 ((wq_completion)dm_bufio_cache){....}-{0:0}, at: process_one_work+0xe46/0x1970 #1: ffffc90000d97d20 ((work_completion)(&dm_bufio_replacement_work)){....}-{0:0}, at: process_one_work+0x763/0x1970 #2: ffffffff8555b528 (dm_bufio_clients_lock){....}-{3:3}, at: do_global_cleanup+0x1ce/0x710 #3: ffff88801d5820b8 (&c->spinlock){....}-{2:2}, at: do_global_cleanup+0x2a5/0x710 Preemption disabled at: [<0000000000000000>] 0x0 CPU: 2 UID: 0 PID: 123 Comm: kworker/2:2 Not tainted 6.16.0-rc3-g90548c634bd0 #305 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 Workqueue: dm_bufio_cache do_global_cleanup Call Trace: <TASK> dump_stack_lvl+0x53/0x70 __might_resched+0x360/0x4e0 do_global_cleanup+0x2f5/0x710 process_one_work+0x7db/0x1970 worker_thread+0x518/0xea0 kthread+0x359/0x690 ret_from_fork+0xf3/0x1b0 ret_from_fork_asm+0x1a/0x30 </TASK> That can be reproduced by: veritysetup format --data-block-size=4096 --hash-block-size=4096 /dev/vda /dev/vdb SIZE=$(blockdev --getsz /dev/vda) dmsetup create myverity -r --table "0 $SIZE verity 1 /dev/vda /dev/vdb 4096 4096 <data_blocks> 1 sha256 <root_hash> <salt> 1 try_verify_in_tasklet" mount /dev/dm-0 /mnt -o ro echo 102400 > /sys/module/dm_bufio/parameters/max_cache_size_bytes [read files in /mnt] | ||||
| CVE-2025-38486 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: soundwire: Revert "soundwire: qcom: Add set_channel_map api support" This reverts commit 7796c97df6b1b2206681a07f3c80f6023a6593d5. This patch broke Dragonboard 845c (sdm845). I see: Unexpected kernel BRK exception at EL1 Internal error: BRK handler: 00000000f20003e8 [#1] SMP pc : qcom_swrm_set_channel_map+0x7c/0x80 [soundwire_qcom] lr : snd_soc_dai_set_channel_map+0x34/0x78 Call trace: qcom_swrm_set_channel_map+0x7c/0x80 [soundwire_qcom] (P) sdm845_dai_init+0x18c/0x2e0 [snd_soc_sdm845] snd_soc_link_init+0x28/0x6c snd_soc_bind_card+0x5f4/0xb0c snd_soc_register_card+0x148/0x1a4 devm_snd_soc_register_card+0x50/0xb0 sdm845_snd_platform_probe+0x124/0x148 [snd_soc_sdm845] platform_probe+0x6c/0xd0 really_probe+0xc0/0x2a4 __driver_probe_device+0x7c/0x130 driver_probe_device+0x40/0x118 __device_attach_driver+0xc4/0x108 bus_for_each_drv+0x8c/0xf0 __device_attach+0xa4/0x198 device_initial_probe+0x18/0x28 bus_probe_device+0xb8/0xbc deferred_probe_work_func+0xac/0xfc process_one_work+0x244/0x658 worker_thread+0x1b4/0x360 kthread+0x148/0x228 ret_from_fork+0x10/0x20 Kernel panic - not syncing: BRK handler: Fatal exception Dan has also reported following issues with the original patch https://lore.kernel.org/all/[email protected]/ Bug #1: The zeroeth element of ctrl->pconfig[] is supposed to be unused. We start counting at 1. However this code sets ctrl->pconfig[0].ch_mask = 128. Bug #2: There are SLIM_MAX_TX_PORTS (16) elements in tx_ch[] array but only QCOM_SDW_MAX_PORTS + 1 (15) in the ctrl->pconfig[] array so it corrupts memory like Yongqin Liu pointed out. Bug 3: Like Jie Gan pointed out, it erases all the tx information with the rx information. | ||||
| CVE-2025-38509 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: reject VHT opmode for unsupported channel widths VHT operating mode notifications are not defined for channel widths below 20 MHz. In particular, 5 MHz and 10 MHz are not valid under the VHT specification and must be rejected. Without this check, malformed notifications using these widths may reach ieee80211_chan_width_to_rx_bw(), leading to a WARN_ON due to invalid input. This issue was reported by syzbot. Reject these unsupported widths early in sta_link_apply_parameters() when opmode_notif is used. The accepted set includes 20, 40, 80, 160, and 80+80 MHz, which are valid for VHT. While 320 MHz is not defined for VHT, it is allowed to avoid rejecting HE or EHT clients that may still send a VHT opmode notification. | ||||
| CVE-2025-38508 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: x86/sev: Use TSC_FACTOR for Secure TSC frequency calculation When using Secure TSC, the GUEST_TSC_FREQ MSR reports a frequency based on the nominal P0 frequency, which deviates slightly (typically ~0.2%) from the actual mean TSC frequency due to clocking parameters. Over extended VM uptime, this discrepancy accumulates, causing clock skew between the hypervisor and a SEV-SNP VM, leading to early timer interrupts as perceived by the guest. The guest kernel relies on the reported nominal frequency for TSC-based timekeeping, while the actual frequency set during SNP_LAUNCH_START may differ. This mismatch results in inaccurate time calculations, causing the guest to perceive hrtimers as firing earlier than expected. Utilize the TSC_FACTOR from the SEV firmware's secrets page (see "Secrets Page Format" in the SNP Firmware ABI Specification) to calculate the mean TSC frequency, ensuring accurate timekeeping and mitigating clock skew in SEV-SNP VMs. Use early_ioremap_encrypted() to map the secrets page as ioremap_encrypted() uses kmalloc() which is not available during early TSC initialization and causes a panic. [ bp: Drop the silly dummy var: https://lore.kernel.org/r/20250630192726.GBaGLlHl84xIopx4Pt@fat_crate.local ] | ||||
| CVE-2025-38507 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: HID: nintendo: avoid bluetooth suspend/resume stalls Ensure we don't stall or panic the kernel when using bluetooth-connected controllers. This was reported as an issue on android devices using kernel 6.6 due to the resume hook which had been added for usb joycons. First, set a new state value to JOYCON_CTLR_STATE_SUSPENDED in a newly-added nintendo_hid_suspend. This makes sure we will not stall out the kernel waiting for input reports during led classdev suspend. The stalls could happen if connectivity is unreliable or lost to the controller prior to suspend. Second, since we lose connectivity during suspend, do not try joycon_init() for bluetooth controllers in the nintendo_hid_resume path. Tested via multiple suspend/resume flows when using the controller both in USB and bluetooth modes. | ||||
| CVE-2025-38505 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: discard erroneous disassoc frames on STA interface When operating in concurrent STA/AP mode with host MLME enabled, the firmware incorrectly sends disassociation frames to the STA interface when clients disconnect from the AP interface. This causes kernel warnings as the STA interface processes disconnect events that don't apply to it: [ 1303.240540] WARNING: CPU: 0 PID: 513 at net/wireless/mlme.c:141 cfg80211_process_disassoc+0x78/0xec [cfg80211] [ 1303.250861] Modules linked in: 8021q garp stp mrp llc rfcomm bnep btnxpuart nls_iso8859_1 nls_cp437 onboard_us [ 1303.327651] CPU: 0 UID: 0 PID: 513 Comm: kworker/u9:2 Not tainted 6.16.0-rc1+ #3 PREEMPT [ 1303.335937] Hardware name: Toradex Verdin AM62 WB on Verdin Development Board (DT) [ 1303.343588] Workqueue: MWIFIEX_RX_WORK_QUEUE mwifiex_rx_work_queue [mwifiex] [ 1303.350856] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 1303.357904] pc : cfg80211_process_disassoc+0x78/0xec [cfg80211] [ 1303.364065] lr : cfg80211_process_disassoc+0x70/0xec [cfg80211] [ 1303.370221] sp : ffff800083053be0 [ 1303.373590] x29: ffff800083053be0 x28: 0000000000000000 x27: 0000000000000000 [ 1303.380855] x26: 0000000000000000 x25: 00000000ffffffff x24: ffff000002c5b8ae [ 1303.388120] x23: ffff000002c5b884 x22: 0000000000000001 x21: 0000000000000008 [ 1303.395382] x20: ffff000002c5b8ae x19: ffff0000064dd408 x18: 0000000000000006 [ 1303.402646] x17: 3a36333a61623a30 x16: 32206d6f72662063 x15: ffff800080bfe048 [ 1303.409910] x14: ffff000003625300 x13: 0000000000000001 x12: 0000000000000000 [ 1303.417173] x11: 0000000000000002 x10: ffff000003958600 x9 : ffff000003625300 [ 1303.424434] x8 : ffff00003fd9ef40 x7 : ffff0000039fc280 x6 : 0000000000000002 [ 1303.431695] x5 : ffff0000038976d4 x4 : 0000000000000000 x3 : 0000000000003186 [ 1303.438956] x2 : 000000004836ba20 x1 : 0000000000006986 x0 : 00000000d00479de [ 1303.446221] Call trace: [ 1303.448722] cfg80211_process_disassoc+0x78/0xec [cfg80211] (P) [ 1303.454894] cfg80211_rx_mlme_mgmt+0x64/0xf8 [cfg80211] [ 1303.460362] mwifiex_process_mgmt_packet+0x1ec/0x460 [mwifiex] [ 1303.466380] mwifiex_process_sta_rx_packet+0x1bc/0x2a0 [mwifiex] [ 1303.472573] mwifiex_handle_rx_packet+0xb4/0x13c [mwifiex] [ 1303.478243] mwifiex_rx_work_queue+0x158/0x198 [mwifiex] [ 1303.483734] process_one_work+0x14c/0x28c [ 1303.487845] worker_thread+0x2cc/0x3d4 [ 1303.491680] kthread+0x12c/0x208 [ 1303.495014] ret_from_fork+0x10/0x20 Add validation in the STA receive path to verify that disassoc/deauth frames originate from the connected AP. Frames that fail this check are discarded early, preventing them from reaching the MLME layer and triggering WARN_ON(). This filtering logic is similar with that used in the ieee80211_rx_mgmt_disassoc() function in mac80211, which drops disassoc frames that don't match the current BSSID (!ether_addr_equal(mgmt->bssid, sdata->vif.cfg.ap_addr)), ensuring only relevant frames are processed. Tested on: - 8997 with FW 16.68.1.p197 | ||||
| CVE-2025-38504 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: io_uring/zcrx: fix pp destruction warnings With multiple page pools and in some other cases we can have allocated niovs on page pool destruction. Remove a misplaced warning checking that all niovs are returned to zcrx on io_pp_zc_destroy(). It was reported before but apparently got lost. | ||||
| CVE-2024-58238 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btnxpuart: Resolve TX timeout error in power save stress test This fixes the tx timeout issue seen while running a stress test on btnxpuart for couple of hours, such that the interval between two HCI commands coincide with the power save timeout value of 2 seconds. Test procedure using bash script: <load btnxpuart.ko> hciconfig hci0 up //Enable Power Save feature hcitool -i hci0 cmd 3f 23 02 00 00 while (true) do hciconfig hci0 leadv sleep 2 hciconfig hci0 noleadv sleep 2 done Error log, after adding few more debug prints: Bluetooth: btnxpuart_queue_skb(): 01 0A 20 01 00 Bluetooth: hci0: Set UART break: on, status=0 Bluetooth: hci0: btnxpuart_tx_wakeup() tx_work scheduled Bluetooth: hci0: btnxpuart_tx_work() dequeue: 01 0A 20 01 00 Can't set advertise mode on hci0: Connection timed out (110) Bluetooth: hci0: command 0x200a tx timeout When the power save mechanism turns on UART break, and btnxpuart_tx_work() is scheduled simultaneously, psdata->ps_state is read as PS_STATE_AWAKE, which prevents the psdata->work from being scheduled, which is responsible to turn OFF UART break. This issue is fixed by adding a ps_lock mutex around UART break on/off as well as around ps_state read/write. btnxpuart_tx_wakeup() will now read updated ps_state value. If ps_state is PS_STATE_SLEEP, it will first schedule psdata->work, and then it will reschedule itself once UART break has been turned off and ps_state is PS_STATE_AWAKE. Tested above script for 50,000 iterations and TX timeout error was not observed anymore. | ||||
| CVE-2025-20346 | 1 Cisco | 2 Catalyst Center, Digital Network Architecture Center | 2025-11-19 | 4.3 Medium |
| A vulnerability in Cisco Catalyst Center could allow an authenticated, remote attacker to execute operations that should require Administrator privileges. The attacker would need valid read-only user credentials. This vulnerability is due to improper role-based access control (RBAC). An attacker could exploit this vulnerability by logging in to an affected system and modifying certain policy configurations. A successful exploit could allow the attacker to modify policy configurations that are reserved for the Administrator role. To exploit this vulnerability, the attacker must have valid credentials for a user account with at least the role of Observer. | ||||
| CVE-2022-50233 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: eir: Fix using strlen with hdev->{dev_name,short_name} Both dev_name and short_name are not guaranteed to be NULL terminated so this instead use strnlen and then attempt to determine if the resulting string needs to be truncated or not. | ||||
| CVE-2025-2534 | 1 Ibm | 1 Db2 | 2025-11-19 | 5.3 Medium |
| IBM Db2 11.1.0 through 11.1.4.7, 11.5.0 through 11.5.9, and 12.1.0 through 12.1.3 for Linux, UNIX and Windows (includes Db2 Connect Server) is vulnerable to a denial of service as the server may crash under certain conditions with a specially crafted query. | ||||
| CVE-2025-12762 | 1 Pgadmin | 1 Pgadmin 4 | 2025-11-19 | 9.1 Critical |
| pgAdmin versions up to 9.9 are affected by a Remote Code Execution (RCE) vulnerability that occurs when running in server mode and performing restores from PLAIN-format dump files. This issue allows attackers to inject and execute arbitrary commands on the server hosting pgAdmin, posing a critical risk to the integrity and security of the database management system and underlying data. | ||||
| CVE-2025-38238 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: scsi: fnic: Fix crash in fnic_wq_cmpl_handler when FDMI times out When both the RHBA and RPA FDMI requests time out, fnic reuses a frame to send ABTS for each of them. On send completion, this causes an attempt to free the same frame twice that leads to a crash. Fix crash by allocating separate frames for RHBA and RPA, and modify ABTS logic accordingly. Tested by checking MDS for FDMI information. Tested by using instrumented driver to: - Drop PLOGI response - Drop RHBA response - Drop RPA response - Drop RHBA and RPA response - Drop PLOGI response + ABTS response - Drop RHBA response + ABTS response - Drop RPA response + ABTS response - Drop RHBA and RPA response + ABTS response for both of them | ||||
| CVE-2025-37898 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: powerpc64/ftrace: fix module loading without patchable function entries get_stubs_size assumes that there must always be at least one patchable function entry, which is not always the case (modules that export data but no code), otherwise it returns -ENOEXEC and thus the section header sh_size is set to that value. During module_memory_alloc() the size is passed to execmem_alloc() after being page-aligned and thus set to zero which will cause it to fail the allocation (and thus module loading) as __vmalloc_node_range() checks for zero-sized allocs and returns null: [ 115.466896] module_64: cast_common: doesn't contain __patchable_function_entries. [ 115.469189] ------------[ cut here ]------------ [ 115.469496] WARNING: CPU: 0 PID: 274 at mm/vmalloc.c:3778 __vmalloc_node_range_noprof+0x8b4/0x8f0 ... [ 115.478574] ---[ end trace 0000000000000000 ]--- [ 115.479545] execmem: unable to allocate memory Fix this by removing the check completely, since it is anyway not helpful to propagate this as an error upwards. | ||||
| CVE-2022-50096 | 1 Linux | 1 Linux Kernel | 2025-11-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: x86/kprobes: Update kcb status flag after singlestepping Fix kprobes to update kcb (kprobes control block) status flag to KPROBE_HIT_SSDONE even if the kp->post_handler is not set. This bug may cause a kernel panic if another INT3 user runs right after kprobes because kprobe_int3_handler() misunderstands the INT3 is kprobe's single stepping INT3. | ||||